DIFFUSER SET FOR MB 900 56062003
- Diffuser set for MB 900 sprayer 56062003 - 3 tips: stream splitter, slowing atomizer and 45° angle atomizer. Precise, gentle spraying of plants, shrubs, hedges and greenhouse crops.
DIFFUSER SET FOR MB 900 56062003 is a complete three-piece accessory kit designed for the MB 900 sprayer, which allows you to precisely direct and regulate the strength of the spray jet. It allows you to adjust the operation of the device for delicate plants, dense plantings and hard-to-reach areas, increasing the efficiency of spraying and the comfort of your work.
The kit includes three different diffusers that easily mount to the outlet of the MB 900 sprayer:
DIFFUSER KIT - allows you to direct or reduce the force of the jet as needed (3 versions): -- Stream splitter creates two streams of working fluid. -- A slowing atomizer reduces spray speed to prevent damage to leaves and flowers. -- Angled atomizer directs the spray at a 45o angle, ideal for plants with leaves, directing the spray from below upward.
Thanks to this simple but extremely effective solution, the MB 900 sprayer gains a whole new level of functionality: you better protect your plants, reach hard-to-reach parts of the crop, and at the same time reduce the risk of mechanical damage caused by too strong a stream of.
What is the diffuser kit for MB 900 56062003 and how it works?
Diffuser set for MB 900 56062003 is a set of three interchangeable caps (tips) mounted on the nozzle outlet of the MB 900 sprayer. Each diffuser is responsible for a different "behavior" of the liquid stream:
- Stream splitter - Divides one strong stream into two smaller ones, allowing the cover a larger area with a single pass and at the same time reduces the unit pressure acting on the leaves or flowers.
- Slowdown atomizer - Reduces jet speed, which is crucial when spraying very delicate ornamental plants, balcony flowers or young seedlings, subject to mechanical damage.
- 45° angle atomizer - changes the direction of the outflow of liquid, directing the jet at an angle of 45° from the bottom to the top. This solution is ideal for spraying plants with large leaves, shrubs, hedges and the underside of leaves.
In practice, this means that, depending on the conditions and type of spray, you can change the tip in seconds to get the optimal effect - from a wide split spray, to a gentle mist, to a precise angled spray.
Where to install the DIFFUSER KIT for MB 900 56062003?
The diffuser set was designed specifically to work with the mB 900 sprayer. Installation is done directly on the working end of the device:
- Diffusers are slid or snapped onto the outlet of the sprayer nozzle, replacing the standard tip or working in conjunction with it - depending on the design of the device.
- The design of the elements is lightweight, yet strong, which ensures stable fastening even when operating at full pressure.
- Replacing the diffuser takes just a moment and requires no additional tools - simply detach one tip by hand and insert the other.
This type of solution is particularly convenient for users who frequently change the type of spraying - for example, once working in the greenhouse, and in a moment at larger plantings in the garden. Instead of adjusting the device itself, you simply install the appropriate diffuser.
Use of diffuser set for MB 900 in garden and professional cultivation
DIFFUSER KIT FOR MB 900 56062003 is used wherever the following counts precision, gentleness and safety of spraying. It is an excellent choice for both demanding amateurs and professional users.
Example application areas:
- Home garden - Spraying of roses, hydrangeas, bedding plants, fruit trees, berry bushes.
- Greenhouses and foil tunnels - Protective treatments on tomatoes, cucumbers, peppers, herbs or lettuce crops where a precise dosage and gentle spray.
- Balconies and terraces - Gentle spraying and protection of potted and box plants, which are easily damaged by too strong a spray.
- Specialty crops - ornamental plants, collections of exotic plants, nurseries of ornamental shrubs, where both the effectiveness of treatments and the intact appearance of plants are important.
With the ability to choose the right nozzle, this set of diffusers significantly increases the functionality of the MB 900 sprayer, allowing you to make the most of its potential in a wide variety of conditions.
Key benefits of using the diffuser kit for MB 900 56062003
The benefits of using a set of diffusers are important, both in terms of the quality of spraying and comfort:
- Full control over the flow of liquid - Depending on the diffuser you choose, you can increase the spray area, reduce the impact force or direct the liquid exactly where it is needed.
- Safety for plants - slowing spray effectively protects delicate leaves, young shoots and flowers against damage from high pressure.
- Improved effectiveness of treatments - A properly selected diffuser allows more precise coverage of the plant surface, including the underside of leaves, which increases the effectiveness of plant protection products and foliar fertilizers.
- Saving time - spray pattern splitter allows spraying two adjacent rows of plants simultaneously, reducing work time on beds and flowerbeds.
- User comfort - the ability to quickly change the nature of the jet without complicated adjustment of the equipment significantly facilitates the work, especially for long-term treatments.
Construction and workmanship of MB 900 diffuser set 56062003
The diffusers are made of high quality plastic, resistant to typical plant protection products and foliar fertilizers used in horticulture and fruit farming. Major design advantages:
- Chemical resistance - materials used in production are suitable for contact with water-based working fluids, fertilizers and plant protection products, which extends the life of diffusers.
- Exact fit for the MB 900 - The shape and diameter of the diffusers are designed to work with the MB 900 sprayer, providing a secure and stable fixing.
- Ease of cleaning - simple design with openwork grilles allows quick rinsing of sediment and dirt under running water, which minimizes the risk of clogging the holes.
The diffuser set is lightweight, handy and convenient to carry - it will easily fit in your garden accessory box or in the glove box of your sprayer so that it is always at hand when you are working.
The use of diffusers in practice - sample scenarios of use
To better illustrate the functionality of the diffuser set for the MB 900, it is useful to trace some typical garden situations:
- Spraying delicate flowers (such as roses, petunias, surfinias) - you put on slowing atomizer. Thanks to the reduced velocity of the jet, you do not break off petals or buds, and the protective formula settles thoroughly on the surface of the plants.
- Treatments on hedges and shrubs with dense foliage - you use 45° angle atomizer, which allows spraying from the bottom up. In this way, you reach the underside of the leaves, where pests often reside, and increase the effectiveness of treatments.
- Quick spraying of larger areas - you mount stream splitter and in one pass you spray two rows of vegetables or ornamental plants, reducing treatment time while maintaining even coverage.
This flexible approach to spraying reduces the use of protection products, improves work safety and increases the health of the entire planting.
Key features of the diffuser kit for MB 900 56062003 from a customer perspective
- Compatibility - product designed specifically for the sprayer MB 900, which guarantees a proper fit and reliable operation.
- Three functions in one set - jet splitter, slowing atomizer and 45° angle atomizer enable wide range of applications.
- Protecting delicate plants - less risk of mechanical damage to leaves and flowers.
- Precision and economy - Better surface coverage with less spray application.
- Easy installation and operation - quick exchange of tips, without the need for tools.
- Durable design - Resistance to chemicals, easy cleaning, long life.
Example technical data (indicative information)
- Purpose: mB 900 sprayer
- Product type: set of diffusers/diffuser tips
- Number of pieces in the set: 3 (jet distributor, slowing atomizer, 45° angle atomizer)
- Material: durable plastic resistant to pesticides
- Color: white
- Intended use: home gardens, allotments, orchards, greenhouses, professional cultivation of ornamental plants
- EAN code: 8026619062200
- Product code: 56062003
Why choose an original diffuser kit for MB 900 56062003?
The original diffuser set for MB 900 56062003 is a guarantee that the accessory is perfectly matched to your device. With this:
- you are assured of safe installation without the risk of accidental slipping of the tip during operation,
- you maintain the full performance and parameters of the sprayer, as intended by the manufacturer,
- you gain accessories designed for everyday, intensive use in the garden or in professional crops.
By investing in an original set of diffusers, you not only increase the comfort and safety of your work, but also take care of the life of the entire equipment, avoiding the risk of using accidental, mismatched accessories.
FAQ - Frequently Asked Questions about DIFFUSER KIT for MB 900 56062003
1. Does the diffuser kit fit other sprayer models than MB 900?
The kit was designed with the sprayer in mind MB 900 and it is with this model that full compatibility and proper operation is guaranteed. Use with other devices depends on their design and outlet diameter - if in doubt, compare dimensions or consult your dealer.
2. How often should diffusers be cleaned?
It is a good idea to rinse with clean water after each completed spray. This will avoid the drying up of crop protection products and contaminants that could, over time, restrict the flow of liquid or change the nature of the stream.
3. Can diffusers be used with all crop protection products?
The diffusers are made of plastic suitable for contact with typical liquid preparations, fertilizers and plant protection products designed for use in sprayers. However, always follow the chemical manufacturer's recommendations and thoroughly rinse the sprayer and accessories after work.
4. Which diffuser to choose for delicate flowering plants?
For plants with delicate leaves and flowers, the following will work best slowing sprayer, which reduces jet velocity and minimizes the risk of mechanical damage, while ensuring good coverage of the crop with the working fluid.
5. How to use a 45° angle sprayer when spraying shrubs?
When spraying shrubs and hedges, it is recommended to guide the nozzle below the crown of the plant and directing the stream upward. This allows the liquid to reach the underside of the leaves and hard-to-reach areas in the dense plant mass, significantly increasing the effectiveness of protective treatments.
6. Does the installation of the diffusers require tools?
Not. Installation and removal of diffusers is done manually. The tips are designed to be easy to put on and take off, while providing a stable and secure attachment during operation.
7. Does the stream splitter increase fluid consumption?
The splitter splits one stream into two, but does not necessarily mean more consumption - In practice, it allows you to spray two rows of plants simultaneously, so you save time, and the amount of liquid per unit area is under your control (you adjust the pace of work and dose).
WARRANTY TERMS AND CONDITIONS
For warranty terms and conditions, please refer to the instruction manual included in the device packaging. Devices covered by the extended warranty (3 and 5 years) require the execution of the mandatory warranty inspections (payable) at the times specified in the warranty terms and conditions.
The obligations of the guarantor under the guarantee are to repair the defective goods, the advertised device is not subject to replacement or cash back.
1. The manufacturer guarantees its products for a period of time:
- Oleo-Mac internal combustion mowers 60 months for consumer use and 12 months otherwise
- Oleo-Mac chainsaws, Oleo-Mac scythes, Oleo-Mac electric mowers, Oleo-Mac trimmers
TR 61 E and TR 91 E, garden tractors. EMAK K-series internal combustion engines powering mowers and
tractors 36 months for consumer use and in other cases 12 months
- Other devices for consumer use 24 months and in other cases 12 months
Additional consumer warranty on Briggs&Stratton engines after the expiration of the manufacturer's warranty period of 12 months -
The condition for maintaining the 36-month warranty period is to perform two paid inspections of the device at an authorized service center - in 12 and 24 month from the date of purchase no later than 7 days after the specified date.
As a condition for maintaining the 60-month warranty period, four paid inspections of the device must be performed at an authorized service center - at 12, 24,36 and 48 months from the date of purchase no later than 7 days after the appointed date. All inspections performed by the dealer must be recorded in the electronic
b2B guarantee settlement system. Internal combustion engines of other brands (Briggs & Stratton, HONDA, KAWASAKI, SUBARU, etc.).) and hydrostatic transmissions are covered by a separate warranty manufacturer. Details of the warranty terms and conditions are contained in separate manuals for the listed components.
2. The warranty covers all damages occurring during the warranty period resulting from the discovery of latent material defects during this period, assembly or technological.
3. The technical staff will proceed with the repair in the time allowed by organizational requirements, always as soon as possible.
4. The choice of how to remove the damage is up to the guarantor, who can remove the defect by repairing the device or replacing the damaged part. Regardless
way of removing the damage, the warranty continues, extended by the time of removal of the damage by the guarantor.
5. Warranty repair can only be carried out on the basis of the device registration in the B2B system or a valid warranty card with proof of purchase.
Failure to register the device, the warranty card or its cancellation will exclude the guarantor's liability under the warranty provided.
6. The user has the right to appeal against the decision of the service point regarding the qualification of the reported failure. The appeal must be submitted only in the form of in writing with a set of documents stating the course of repairs made and a description of the technical condition of the equipment at the time of the original inspection made by the service point.
7. The warranty period is extended by the time necessary for warranty repair. The dates posted on the claim in the b2B electronic guarantee settlement system.
8. The repair shop is required to make entries regarding the scope of warranty repairs in the B2B electronic warranty billing system.
9. For paid repairs performed, the guarantor provides a 3-month warranty on the condition that the repair is carried out in the guarantor's workshop and that the repair is used for the repair original spare parts. The basis for the claim is the proof of purchase of parts and the service performed.
10. Warranty repair is not subject to: damage caused by improper operation, damage caused by using the device for purposes for which it is not intended, damage caused by the use of improper consumables, mechanical damage, and
caused by improper transportation or storage, damage caused by lack of maintenance, components that have suffered wear and tear in service during proper operation.
11. The warranty is voided as a result of structural changes or modifications made by the user, as a result of interference found by the service point
inside the device by unauthorized persons, as a result of breaking or dismantling the carburetor adjustment locks, in the event that entries are found to have been made in the warranty card by unauthorized persons.
12. The warranty does not cover consumable items and items that wear out during the warranty period, such as:
- Consumable components, e.g.: cutting blades, discs, cutting bars, vee heads, filters, starter cables, spark plugs, bulbs, wheels, drums and clutch jaws,
clutches and friction discs, drive belts, safety bolts, cutting chains and guides, high-pressure washer lances.
- Engine components: cylinders, pistons, rings, crankshaft, bearings, pan, carburetor diaphragms.
- Other consumable parts: knife hubs, safety keyways, shock absorbers, bearings, pan, gears, overload fuses, carbon brushes, control ties and cables
- Starting batteries used in machines with an electric starter
- Components not mentioned in these warranty conditions , which obviously wear out during operation, transportation and storage (such as coating painting).
13. Warranty repair does not include installation, adjustment and maintenance activities.
14. Damage such as engine seizure, bent or cracked crankshaft, broken magnet wheel keyway or knife hub are not repairable warranty.
15. If the service center does not fulfill its obligations, the user is obliged to inform the guarantor of this fact. Refusal to comply repair by the service center must be entered in the warranty card. If the guarantor does not recognize the repair as a warranty repair, the cost of repair and transport is covered by the claimant.
16. Defective spare parts replaced under warranty repair are the property of the guarantor.
17. Complaint should be reported to the nearest authorized service center or directly to the guarantor. Reporting a complaint at the point of sale may cause an increase in repair time.
18. During the reception of the device after warranty repair, it is his duty to make sure that the received device is complete and undamaged. The repair point has the obligation to start the device before handing it over to the user after repair.
19. The service point has the right to charge a fee for performing maintenance activities that are the responsibility of the user and require them to be performed before the proceeding with the repair. The repair shop is obliged to replace, at the user's expense, all components that ensure the safety of the work, which have been damaged damage during operation regardless of the consent of the user.
20. A continuously updated list of service points can be found at www.victus.en
21. The warranty for the goods sold does not exclude, limit or suspend the buyer's rights under the warranty provisions for defects in the goods sold.
22. The cost of an unjustified complaint is paid by the complainant.
23. This warranty is valid in the territory of the Republic of Poland.
24. Any damage caused during transport should be immediately reported to the carrier under penalty of voiding the warranty.
25. The warranty does not cover possible damages caused directly or indirectly to persons or things due to defects in the device or resulting from prolonged downtime in the operation of the device.