LEFT KNIFE 460MM FOR OM90C/91C/91PLUS/92C/93/93C / GLX20-92 SERIES TRACTOR G182004344E1
- Left blade 460 mm G182004344E1 for OM90C/91C/91PLUS/92C/93/93C and GLX20-92 tractors. Precise cutting, high durability, perfect fit, less vibration and professional lawn finish.
LEFT BLADE 460MM FOR OM90C/91C/91PLUS/92C/93/93C / GLX20-92 SERIES TRACTOR G182004344E1 - PROFESSIONAL BLADE FOR PRECISION GRASS CUTTING
The 460mm left blade for OM90C/91C/91PLUS/92C/93/93C / GLX20-92 G182004344E1 series tractor is a high-quality cutting element designed for garden tractors, which ensures clean and even mowing even on demanding lawns. Thanks to its precise workmanship, properly sized and solid steel, it is a part that significantly increases the comfort and efficiency of work in the garden. An ideal choice for both private users and companies engaged in professional care of green areas.
What is the left 460mm blade G182004344E1 and what tractors it fits to?
The presented left-hand 460 mm blade is an original (or fully compatible replacement) cutting element mounted on garden tractors with a working width of about 92 cm. It is designed for tractor models of the series:
- OM90C
- OM91C
- OM91PLUS
- OM92C
- OM93
- OM93C
- GLX20-92
It is a left-hand cutting blade, which means that it is mounted on the left side of the mower deck (viewed from the position of the operator sitting on the tractor). Its task is to cut the blades of grass and direct the swath flow accordingly - into the ejection channel, basket or mulching system (depending on the mower-tractor configuration).
Properly adjusted dimensions and mounting holes make the G182004344E1 knife safe to use and do not cause vibrations that could lead to faster wear of bearings, drive belt or cutting unit components.
Where the left 460mm blade for OM90C/91C/91PLUS/92C/93/93C / GLX20-92 series tractor is mounted?
Left 460 mm blade is mounted directly in the cutting unit (deck) of the garden tractor. It is a component connected to a knife shaft driven by a belt from the engine. The OM90C/91C/91PLUS/92C/93/93C and GLX20-92 series tractors use a system of two blades working simultaneously - left and right - which complement each other to form a wide cutting belt.
The knife is fixed with a central screw and side holes, which can be used for stabilization or installation of additional elements (e.g. washers, brackets). Proper installation is crucial for operator safety - always screw the blade in accordance with the tractor manufacturer's recommendations, using the correct tightening torque and bolt security.
In practice, knife replacement is most often done during:
- seasonal inspection of the tractor,
- dulling or chipping of the cutting edge,
- mechanical damage to the knife (hitting a stone, root, curb),
- upgrading the mower set when the user expects better cutting quality.
Use of the left-hand blade G182004344E1 in daily lawn care
Left blade 460mm G182004344E1 is used wherever it is important to quickly and efficiently mow larger areas of lawn. It works well in home gardens as well as on larger properties, corporate sites, recreational plots or playing fields. With a properly designed profile, it provides:
- accurately cut the grass at the set height,
- a nice, even finish to the surface of the lawn,
- optimum swath ejection for easy collection or mulching.
Regular replacement of cutting blades with sharp and unworn ones has a direct impact on the condition of the lawn. A dull, chipped knife jerks the blades of grass, causing them to turn yellow and make them more susceptible to disease. The use of the new, properly balanced blade translates into a healthier, denser and intensely green lawn, which is especially important for those who care about the aesthetics of their home or business surroundings.
Key technical features of the left 460mm blade for the GLX20-92 G182004344E1 tractor
Precise matching of dimensions and mounting holes is a guarantee of trouble-free use. The left-hand knife 460mm for the OM90C/91C/91PLUS/92C/93/93C / GLX20-92 G182004344E1 series tractor is characterized by the following parameters:
| Overall length | 460 mm |
| Knife width | 55 mm |
| Central hole diameter | 18 mm |
| Diameter of side openings | 8.5 mm |
| Distance between holes | 65 mm |
| Destination | OM90C/91C/91PLUS/92C/93/93C series tractors; GLX20-92 |
| Product code | G182004344E1 |
The exact dimensions ensure a perfect fit with the original handles on the cutting unit. This ensures that the blade runs smoothly, without excessive vibration, and the tractor drive is not overloaded. The steel construction and the appropriate profile of the cutting edge make it possible to mow both freshly sprouted grass and slightly taller, dense clumps.
Utility advantages - durability, reliability and comfort
The 460mm left-hand knife G182004344E1 is designed for long-lasting use in demanding garden conditions. Thick, properly hardened steel and uniform, precision machining make it resistant to:
- the impact of small pebbles and twigs,
- intensive, regular use throughout the season,
- deformation and excessive rubbing of cutting edges.
By using an original or properly matched knife, you are assured:
- The tractor will run evenly and quietly - without unpleasant vibrations.
- The engine and drivetrain will not be excessively stressed - extending their service life.
- The mowing effect will remain high even with frequent use.
All of this translates into real benefits for the user: less time spent on corrections, lower service costs, and the satisfaction of a perfectly mowed lawn.
How you will use the 460mm left-hand knife G182004344E1 in practice - examples of applications
The new left blade for the OM90C/91C/91PLUS/92C/93/93C and GLX20-92 series of tractors will work well in many everyday situations:
- Care of the home garden - Quick, precise mowing of large areas around the house without leaving fraying grass or clumps of uncut areas.
- Maintenance of company grounds - aesthetically trimmed lawn in front of the office, production hall or service facility positively affects the image of the company.
- Recreational plots and allotment gardens - Convenient mowing of longer grass after a long absence, including in areas with more varied terrain.
- Playing fields and sports areas - even length of grass provides better conditions for recreation and sports.
In each of these situations, the quality of the cutting knife is crucial. Replacing a worn blade with a new left-hand blade G182004344E1 immediately improves the efficiency of the tractor, reduces fuel consumption (the engine does not have to "tire" with a dull blade) and reduces the time required to achieve a perfect result.
Installation and maintenance of the 460mm left-hand knife - safety first
In order for the left 460mm blade for the OM90C/91C/91PLUS/92C/93/93C / GLX20-92 tractor to work reliably for a long time, it is worth remembering a few rules of installation and operation:
- Disconnect the power to the tractor - always remove the ignition key and, if possible, disconnect the spark plug wire before starting any service work.
- Position the tractor stably - Raise the cutting unit or tilt the machine in a safe manner using wedges or a jack.
- Protect the knife from rotation - when unscrewing the retaining screw, use a suitable wrench, and block the knife itself with a piece of wood so that it does not turn with the wrench.
- Check the direction of installation - the knife has a working side (cutting edge) and is profiled in a specific direction. Reverse mounting will result in worse mowing and may be dangerous.
- Regularly check the condition of the blade - minor damage can be repaired by sharpening, but for major chipping or deformation, it is recommended to replace the knife with a new one.
Systematic inspection of the technical condition of the blade and its attachment minimizes the risk of failure during operation and ensures complete safety of the operator.
Why choose the 460mm left blade G182004344E1 for your tractor?
When you choose a 460mm left blade for OM90C/91C/91PLUS/92C/93/93C / GLX20-92 G182004344E1 series tractor, you are investing in a part that has a direct impact on the end result of mowing and the life of your machine. It's a solution that connects:
- fit reliability - compatibility of dimensions and mounting holes with the cutting units of the indicated models,
- high quality material - Resistance to wear and tear and mechanical damage,
- convenience - Even operation, less vibration, better tractor culture,
- saving time and money - fewer fixes, less frequent repairs to the drive and genset.
This makes it an ideal choice for those who expect trouble-free operation of the tractor for many seasons and appreciate the professional mowing effect.
Technical data - left knife 460MM FOR OM90C/91C/91PLUS/92C/93/93C / GLX20-92 series tractor G182004344E1
- Length: 460 mm
- Width: 55 mm
- Center hole diameter: 18 mm
- Side hole diameter: 8.5 mm
- Distance between holes: 65 mm
- Purpose: OM90C/91C/91PLUS/92C/93/93C series tractors; GLX20-92
- Type: left blade for cutting unit
- Product code: G182004344E1
FAQ - Frequently asked questions about 460mm left-hand knife G182004344E1
1. Will this knife fit my OM91PLUS tractor?
Yes, the presented 460mm left knife G182004344E1 is designed for OM91PLUS series tractors, as well as OM90C, OM91C, OM92C, OM93, OM93C and GLX20-92, among others. Before buying, it's a good idea to compare the dimensions and hole diameters with the knife you've used so far.
2. Do I have to replace both knives (left and right) at the same time?
It is recommended to replace the blades in pairs. As a result, you will get even operation of the cutting unit, less vibration and better mowing effect. Replacing just one badly worn blade can cause uneven operation of the cutting system.
3. How often should I replace the blade in the tractor?
Frequency of replacement depends on the intensity of use and operating conditions. For typical backyard use, seasonal sharpening and periodic replacement every few seasons is usually sufficient. However, if you frequently mow areas with rocks, molehills or branches, the blade may need to be replaced more often.
4. Is the knife balanced at the factory?
Yes, the new knife is factory-balanced to ensure smooth operation and minimize vibration. After self-sharpening, it is always a good idea to check the balance of the knife - if there is a large difference in weight on both sides, it is recommended to return it to a professional service or replace it with a new one.
5. Is it possible to install this knife yourself?
Yes, the installation of the blade can be done by the user himself, provided that basic safety rules are observed and the tractor manufacturer's instructions are followed. Be sure to have the correct mounting direction and tighten the mounting screw properly.
6. Which means that it is a "left" knife?
The term "left" refers to the position of the blade in the cutting unit and its direction of operation. In tractors with two knives, one is left, the other right. Using the wrong type can result in improper grass shedding and reduced mowing quality.
7. How to take care of a knife to make it last as long as possible?
After each mowing, it's a good idea to clean the blade of grass and soil debris to prevent corrosion. Avoid mowing areas with lots of rocks and hard obstacles. Regularly inspect the condition of the cutting edge and attachment - if there are any visible cracks, deformations or deep cavities, the knife should be replaced immediately.
WARRANTY TERMS AND CONDITIONS
For warranty terms and conditions, please refer to the instruction manual included in the device packaging. Devices covered by the extended warranty (3 and 5 years) require the execution of the mandatory warranty inspections (payable) at the times specified in the warranty terms and conditions.
The obligations of the guarantor under the guarantee are to repair the defective goods, the advertised device is not subject to replacement or cash back.
1. The manufacturer guarantees its products for a period of time:
- Oleo-Mac internal combustion mowers 60 months for consumer use and 12 months otherwise
- Oleo-Mac chainsaws, Oleo-Mac scythes, Oleo-Mac electric mowers, Oleo-Mac trimmers
TR 61 E and TR 91 E, garden tractors. EMAK K-series internal combustion engines powering mowers and
tractors 36 months for consumer use and in other cases 12 months
- Other devices for consumer use 24 months and in other cases 12 months
Additional consumer warranty on Briggs&Stratton engines after the expiration of the manufacturer's warranty period of 12 months -
The condition for maintaining the 36-month warranty period is to perform two paid inspections of the device at an authorized service center - in 12 and 24 month from the date of purchase no later than 7 days after the specified date.
As a condition for maintaining the 60-month warranty period, four paid inspections of the device must be performed at an authorized service center - at 12, 24,36 and 48 months from the date of purchase no later than 7 days after the appointed date. All inspections performed by the dealer must be recorded in the electronic
b2B guarantee settlement system. Internal combustion engines of other brands (Briggs & Stratton, HONDA, KAWASAKI, SUBARU, etc.).) and hydrostatic transmissions are covered by a separate warranty manufacturer. Details of the warranty terms and conditions are contained in separate manuals for the listed components.
2. The warranty covers all damages occurring during the warranty period resulting from the discovery of latent material defects during this period, assembly or technological.
3. The technical staff will proceed with the repair in the time allowed by organizational requirements, always as soon as possible.
4. The choice of how to remove the damage is up to the guarantor, who can remove the defect by repairing the device or replacing the damaged part. Regardless
way of removing the damage, the warranty continues, extended by the time of removal of the damage by the guarantor.
5. Warranty repair can only be carried out on the basis of the device registration in the B2B system or a valid warranty card with proof of purchase.
Failure to register the device, the warranty card or its cancellation will exclude the guarantor's liability under the warranty provided.
6. The user has the right to appeal against the decision of the service point regarding the qualification of the reported failure. The appeal must be submitted only in the form of in writing with a set of documents stating the course of repairs made and a description of the technical condition of the equipment at the time of the original inspection made by the service point.
7. The warranty period is extended by the time necessary for warranty repair. The dates posted on the claim in the b2B electronic guarantee settlement system.
8. The repair shop is required to make entries regarding the scope of warranty repairs in the B2B electronic warranty billing system.
9. For paid repairs performed, the guarantor provides a 3-month warranty on the condition that the repair is carried out in the guarantor's workshop and that the repair is used for the repair original spare parts. The basis for the claim is the proof of purchase of parts and the service performed.
10. Warranty repair is not subject to: damage caused by improper operation, damage caused by using the device for purposes for which it is not intended, damage caused by the use of improper consumables, mechanical damage, and
caused by improper transportation or storage, damage caused by lack of maintenance, components that have suffered wear and tear in service during proper operation.
11. The warranty is voided as a result of structural changes or modifications made by the user, as a result of interference found by the service point
inside the device by unauthorized persons, as a result of breaking or dismantling the carburetor adjustment locks, in the event that entries are found to have been made in the warranty card by unauthorized persons.
12. The warranty does not cover consumable items and items that wear out during the warranty period, such as:
- Consumable components, e.g.: cutting blades, discs, cutting bars, vee heads, filters, starter cables, spark plugs, bulbs, wheels, drums and clutch jaws,
clutches and friction discs, drive belts, safety bolts, cutting chains and guides, high-pressure washer lances.
- Engine components: cylinders, pistons, rings, crankshaft, bearings, pan, carburetor diaphragms.
- Other consumable parts: knife hubs, safety keyways, shock absorbers, bearings, pan, gears, overload fuses, carbon brushes, control ties and cables
- Starting batteries used in machines with an electric starter
- Components not mentioned in these warranty conditions , which obviously wear out during operation, transportation and storage (such as coating painting).
13. Warranty repair does not include installation, adjustment and maintenance activities.
14. Damage such as engine seizure, bent or cracked crankshaft, broken magnet wheel keyway or knife hub are not repairable warranty.
15. If the service center does not fulfill its obligations, the user is obliged to inform the guarantor of this fact. Refusal to comply repair by the service center must be entered in the warranty card. If the guarantor does not recognize the repair as a warranty repair, the cost of repair and transport is covered by the claimant.
16. Defective spare parts replaced under warranty repair are the property of the guarantor.
17. Complaint should be reported to the nearest authorized service center or directly to the guarantor. Reporting a complaint at the point of sale may cause an increase in repair time.
18. During the reception of the device after warranty repair, it is his duty to make sure that the received device is complete and undamaged. The repair point has the obligation to start the device before handing it over to the user after repair.
19. The service point has the right to charge a fee for performing maintenance activities that are the responsibility of the user and require them to be performed before the proceeding with the repair. The repair shop is obliged to replace, at the user's expense, all components that ensure the safety of the work, which have been damaged damage during operation regardless of the consent of the user.
20. A continuously updated list of service points can be found at www.victus.en
21. The warranty for the goods sold does not exclude, limit or suspend the buyer's rights under the warranty provisions for defects in the goods sold.
22. The cost of an unjustified complaint is paid by the complainant.
23. This warranty is valid in the territory of the Republic of Poland.
24. Any damage caused during transport should be immediately reported to the carrier under penalty of voiding the warranty.
25. The warranty does not cover possible damages caused directly or indirectly to persons or things due to defects in the device or resulting from prolonged downtime in the operation of the device.